ETS 16 Installation Guide download pdf (Page 51)

Troubleshooting

ETS Installation Guide 51

Figure B-1. BCP Command Examples

Boot> SET IPADDRESS 192.0.1.229

Boot> SET SOFTWARE /tftpboot/ETS*.SYS

Boot> SET LOADHOST 192.0.1.188

Boot> SET SECONDARY 192.0.1.22

Boot> FLASH

% Initialization begins in 5 seconds.....

These commands set the Server’s address, the software loadfile, and the loadhost’s

IP address (as well as that of a backup loadhost). The server then reboots using the

Flash command and will attempt to load the file ETS*.SYS from the host at

192.0.1.188.

Flush NVR This command is used to restore the ETS’

non-volatile RAM to its factory default

settings. It will reset everything that is

configurable on the server, including the

unit’s IP address.

Flash This command will force the ETS to

download new operational code and reload

it into Flash ROM. This is necessary when a

new version of software is released and you

wish to upgrade your unit. If the server

cannot download the file, the code in Flash

ROM will still be usable.

Help Displays a one-page summary of available

commands and what they do.

Init 451 Reboots the ETS after it has been

configured. If the ETS can find and load the

specified software loadfile, it will restart itself

with full functionality. If the loadfile is not

found, the server will attempt to reload

continuously. If there is an error, or if the

console’s Return key is pressed, the ETS

will re-enter the Boot Configuration

Program.

SET BOOTP {Enabled, Disabled} Enables or disables the sending of BOOTP

queries during the boot sequence. It is

enabled by default.

SET DHCP {Enabled, Disabled} Enables or disables the sending of DHCP

queries during the boot sequence. It is

enabled by default.

SET Hardware xx-xx-xx Specifies the last three numbers of the

server’s Ethernet address. The first three

numbers will be supplied automatically.

The Ethernet address should have been set

at the factory. Setting an incorrect address

could cause serious network problems.

SET IPAddress ip_address Specifies this server’s IP address. Uses the

standard numeric format.

SET Loadhost ip_address Specifies the host to attempt to load the file

from. The IP address should be in standard

numeric format (no text names are allowed).

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 67 68

Comments to this Manuals

No comments

Models	Document Type
08V67-TE0-100A	User Manual HONDA 08V67-TE0-100A User Manual, 15 pages
2007 Accord Cargo Hook	User Manual HONDA 2007 Accord Cargo Hook User Manual, 4 pages
GX200	User Manual HONDA GX200 User Manual, 60 pages
Fuse	User Manual HONDA Fuse User Manual, 3 pages
GCV190	User Manual HONDA GCV190 User Manual, 48 pages
2008 Accord 00X31 TA5 8000	User Manual HONDA 2008 Accord 00X31 TA5 8000 User Manual, 149 pages
EX	User Manual HONDA EX User Manual, 4 pages
2008 Accord Cargo Management	User Manual HONDA 2008 Accord Cargo Management User Manual, 4 pages
GXV620	User Manual HONDA GXV620 Benutzerhandbuch, 55 pages
Music Link AAM 31052-31557	User Manual HONDA Music Link AAM 31052-31557 User Manual, 34 pages

ETS 16 Installation Guide Page 51

Comments to this Manuals

Honda GX270 manuals

Honda GX270 User Manual (52 pages)

Table of contents

Honda GX270 User Manual (60 pages)

Table of contents

More products and manuals for For the car Honda